How To Program Caddx Nx 8 Wiring

How To Program Caddx Nx 8 Wiring Manual
Caddx Nx 8 Installation Manual
How To Program Caddx Nx 8 Wiring Instructions

ARMING IN “EXIT” MODE EXIT is used when the user is away from the premises

Press 0-# to program functions of the NX-8 master control panel itself. Enter the location number you wish to display/alter, followed by the # key. Enter the desired new data, followed by the. View and Download GE NX-1308E - Caddx 8 Zone LED Keypad installation and startup manual online. NX-1308E - Caddx 8 Zone LED Keypad control panel pdf manual download. Select the module to program. Since all modules connected to the NX-8V2 are programmed through the keypad, the module you are programming should be the first entry. To select the module to program, enter 0, #. The 0 is the module number of the control, and # is the entry key.

and wants the interior protected (the motion detectors ON).

1. Close all protected doors and windows.

ARMING IN “STAY” MODE STAY is used when the user is inside the premises and

wants protection around the perimeter (the motion

detectors OFF).

How To Program Caddx Nx 8 Wiring Manual

2. Press the “STAY” key.

DISARMING SYSTEM Enter code.

2. Enter a master code. The “ready” light will flash.

3. Enter the 2-digit user number (example: “03” for user

4. Enter the new 4-digit user code. Note: To delete a

user code, enter * * * * for a 4-digit code.

5. The ready light will flash. If the code is rejected, the

6. If another user code needs to be programmed,

7. Press the “#” key while the ready light is flashing to

exit the User Code Programming Mode.

BYPASSING ZONES System must be in disarmed state.

2. Enter 1 or 2 digits indicating the zone you wish to

Download lockdown browser for canvas. bypass. (Example: Press the “1” key for zone 1,

Caddx Nx 8 Installation Manual

press “1” then “2” for zone 12.)

4. The corresponding zone light will illuminate indicating

the zone has been bypassed. Repeat steps #2 and #3 for

any other zone(s) that need to be bypassed.

5. Press the “#” key to exit the Bypass Mode. The bypass

Ibis paint x download for mac. light will stop flashing upon exiting the Bypass Mode.

Will bluestacks work on mac. All zones will automatically be unbypassed each time the

system is disarmed.

VIEW ALARM MEMORY 1. Press “8” “3.” The zone(s) that created the last alarm

2. The ALARM MEMORY feature will flash those zones

that created alarms and will light steady those zones that

were bypassed during the last alarm.

IDENTIFYING TROUBLES

FLASHING ARMED LIGHT The armed light will flash when there has been

an alarm during the previous arm cycle.

POWER LIGHT OFF No AC power.

POWER LIGHT FLASHING Low system battery.

FIRE LIGHT FLASHING Trouble with fire device or wiring.

ZONE LIGHT FLASHING RAPIDLY A zone is in a trouble condition.

SERVICE LIGHT IS ON Press “*2” for further information (indicated by

zone lights).

How To Program Caddx Nx 8 Wiring Instructions

Zone 1 – System fault.

Zone 2 – Zone tamper.

Zone 5 – Zone trouble.

Zone 6 – Telephone trouble.

Zone 7 – Dialer failure.

Zone 8 – System lost time.

Enter “#” to exit mode.

ENTER CODE TO SILENCE TROUBLE BEEPS.

ENTER “*7” TO ATTEMPT TO RESET TROUBLES.

ENTER CODE TO CLEAR SERVICE LIGHT AFTER A PHONE TROUBLE HAS BEEN CLEARED.

SET CLOCK 1. Press “*97.”

3. Enter time as 4-digit military time.

Keebler Crackers Expiration Date Load

3 Sweep Mac